PERFECTPERFECT page 1Universal oven UNP 200-800UFP 400-800SteriliserSFP 400-800Incubator INP 200-800Operating Instructions
PERFECT page 105 Oven construction and operationOvens Series UNP and INP have natural ventilation.In Series UFP and SFP ovens, air circulation is pro
PERFECTsetoffonpushcard4321STERI DEFROrhmb%COmb2IN 1IN 2OUTIN 1IN 2OUTPRINTSETUPloopt3t4t2t1onoffMoTuWeThFrSa Su°C°CMINAUTOMAXh page 115.2 Controls a
PERFECTloopt1t2t3t4loopt1t2t3t4page 126 Selecting the operating modePRINTSETUPAfter holding down the SET key (approx. 3 sec), the current oper
PERFECT page 138 Normal operation PRINTSETUPIn this operating mode the oven operates continuously. The settings for operating the oven can be selecte
PERFECT page 14Setting example “Normal operation“The oven (UFP500) has to heat up to 180°C at 50% fan speed and with the air valve 20%
PERFECT page 159 Weekly programmer PRINTSETUPIn this operating mode the weekly programmer is activated and the oven switches on and off automatically
PERFECT page 16Programming example “Weekly programmer“The oven (UFP500) has to switch on at 07.30 hrs from Mo to Fr (workday group) and switch off at
PERFECT page 1710 Programme operation PRINTSETUPIn this operating mode, up to 40 freely programmable temperature-time ramps can be set. Rotating the
PERFECT page 18PRINTSETUPloopt3t4t2t1onoffMoTuWeThFrSa SuMAX°Ch°CDuration of first ramp segmentRange: 1 minute to 999 hours.PRINTSETUPloopt3t4t2t1onof
PERFECT page 1910.1 Closure commands for ramp segmentsNEXT Follow-on with next programme segment.SPWT (T)SET-POINT WAITWait until the setpoint temper
PERFECT page 21. Contents1 Contents ...
PERFECT page 20Programming example programme operationThe oven (UFP500) has to heat up as quickly as possible to 180°C on Monday at 08.00 hrs with a f
PERFECT page 215. Select duration of first ramp segmentTurn the push/turn control further clockwise until the time of the first ramp segment is flashi
PERFECT page 2214. Set closure command for second ramp segmentTurn the push/turn control clockwise until a segment closure command (e.g end ) appears.
PERFECT page 2311 Printer PRINTPRINTSETUPAll PERFECT ovens are fitted as standard with a parallel printer interface, as used on personal computers.Th
PERFECT page 2412 Basic oven settings SETUPPRINTSETUPIn this operating mode it is possible to make the basic settings of the oven. Clock time, date,
PERFECT page 25Heater power reductionfor gentle heating of the load and reduction of the mean current taken from the power supply.Note: reduction in
PERFECT page 2613 Temperature monitor and protection devicesThe monitor temperature is measured with a separate PT100 temperature sensor inside the c
PERFECT page 2713.2 Electronic temperature monitor13.2.1 Overtemperature protection MAXRange: up to 10°C max above nominal temperature (for nominal t
PERFECT page 28The manually set monitor temperature and the electronic overtemperature protection are monitored on PERFECT incubators by an adjustable
PERFECT page 2913.2.5 Automatic temperature monitor (ASF) AUTOA monitoring device which automatically follows the selected temperature setpoint.The t
PERFECT page 315 Communication interface for the PC...3415.
PERFECT page 30Going outside tolerance margin = ASF alarmGoing outside the selected tolerance margin of the setpoint (in the example 150°C +/-10°C), f
PERFECT page 31Setpoint changed = ASF de-activated automaticallyIf the temperature setpoint is altered, the automatic temperature monitor is automatic
PERFECT page 3214 CalibrationUser-calibration of oven and controller, with three calibration temperatures selected by the user.CAL1 temperature cali
PERFECTh˚C˚Ch˚C˚Ch˚C˚C page 33Note:If all calibration corrections are set to 0.0°C the factory calibration is restored.Calibration correction Range
PERFECT page 3415 Communication interface for the PC15.1 Communication interface RS232CThe oven is provided as standard with a serial communication
PERFECT page 3515.2 Bus interface RS485When so ordered, the oven can be equipped at the factory with an RS485 interface instead of the RS232C interfa
PERFECT page 3616 Heating power distribution BALANCEOn ovens series INP 500-800 and UNP/UFP 400-800 it is possible in SETUP to correct the heating po
PERFECT page 3717 Report memoryThe controller continuously records all relevant measurements, settings and error messages at 1-minute intervals.The i
PERFECT page 3818 Memory card: MEMoryCard XLA temperature programme with up to 40 ramps can be programmed on the MEMoryCard XL. Programming can take
PERFECT page 39Note:The programme remains stored on the Memory Card XL after the card has been removed from the unit. It can however be overwritten at
PERFECT page 4This mark in the Operating Instructions means:Watch outImportant Note2 General notes and safety notesYou have purchased a technically f
PERFECT page 4019 Sterilisation chip card (for INP incubators only) SterilisationProcess ControlCardSterilisation Parameter:160 °C / 4:00 hUnit-ID: _
PERFECT page 4120 User-ID-Card (available as optional extra) access authoritycardName:ID:__________________________________________The User-ID-Card s
PERFECT page 4221 Sterilisers21.1 Purpose definition for MEMMERT hot air sterilisersThe oven SFP is intended for the sterilisation of medical materi
PERFECT page 43The following table gives typical values for the holding time to be set, with different amounts of load, for sterilisers with and witho
PERFECT page 44Programming example steriliserThe steriliser (SFP600) has to sterilise at a temperature of 180°C and a medium quantity of load for one
PERFECT page 457. Set air valve for first ramp segmentTurn the push/turn control clockwise until the air valve symbol is flashing.Hold down
PERFECT page 4614. Select duration of third ramp segmentUsing the push/turn control select the time indicationHold down the SET key and set the
PERFECT12 page 4722. Set air valve for fourth ramp segmentTurn the push/turn control clockwise until the air valve symbol is flashing.Hold d
PERFECT123465page 4822 CleaningRegular cleaning of the easy-to-clean inside of the chamber prevents deposits which over time can detract from the app
PERFECT page 4924 Error messagesE-0 Error on self testE-1 Power module triac faultyE-2 Power module faultyE-3 PT100 temperature probe faultyE-L1 Erro
PERFECT page 5 15 cm min. 8 cm min. 8 cm min. 20 cm min.3 Installation facilities (accessories)The oven can be placed on the floor or
PERFECT page 5026 CE Conformity Declaration Modelljahr 2003 D09932 / 03.07.08EC Declaration of Conformity Manufacturer´s name and address: MEMMERT
PERFECT page 51 Modelljahr 2003 D09937 / 03.07.08EC Declaration of Conformity Manufacturer´s name and address: MEMMERT GmbH + Co. KG Äußere Ritters
PERFECT page 52 EC Declaration of Conformity Manufacturer´s name and address: MEMMERT GmbH + Co. KG Äußere Rittersbacher Straße 38 D-91126 Schwa
PERFECT page 53Standard ovens (UNP / UFP / INP) are safety-approved and bear the test marks: Sterilisers (SFP) are safety-approved
PERFECT page 5428 IndexAaccessories 9address 53air supply 10air valve 13air valve indication 11alarm indication 11alarm symbol 26, 28ASF 29aut
PERFECT page 55
PERFECT page 5620.08.2008PERFECT englischD09805
PERFECT page 63.4 Initial start-upWhen the oven is started up for the first time, it should be supervised continuously until steady conditions have b
PERFECT page 74 Technical datasupply plugconnection RS232Cprinter connectionModel 200 300 400 500 600 700 800Chamber width A [mm] 400 480 400 560 800
PERFECT page 84.1 Standard equipment of PERFECT ovensElectronic fuzzy-supported PID process controller with permanent power matching and time-saving
PERFECT page 9WARNING! Always pull out the supply plug before opening the oven cover!4.3 Electrical equipmentOperating voltage see label 50/60 Hz•C
Kommentare zu diesen Handbüchern